The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) is compatible wired with: All gate openers for 24-volt gate openers a 12-volt transformer will be needed (not included)
GateCrafters.com offers more expert assistance than anyone. We have live application specialists available 9 am - 9 pm EST 7 days a week.
The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) has the ability to control two separate devices or two different relays on a control board and can learn up to 400 codes. The typical situation for the receiver controlling two devices in a 3 car garage. Usually, there are 2 separate garage door openers in this type of garage and you can utilize the one receiver to control each one of them with a separate button on the remote. Another option for using the two relays on the receiver is controlling two separate terminals on a single gate opener. Many times gate openers will have a terminal for an automated open and close and another terminal for partial opening or open only during re-closing without stopping. A second button on the remote could be used to control this second function.
This receiver is also a plug-in receiver for Estate Swing gate openers. Please see the drop-down options.
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition, we have the largest staff of factory trained technicians in the US.
Easy Wiring: There are 4 or 6 wires that you need to connect depending on if you are using 1 or 2 channels. Two are for power, which can be AC or DC 12-24V. If you cannot find a power source (most gate openers have a battery you can run it off of) then you can hook it up to a transformer. (Search your junk drawers, many old transformers from other electronics may fall within the generous range allowed by our receiver). The other two wires close a circuit. On a garage door simply find the two terminals that the wall mount button uses.
Strong Range: This is one of the best features of this receiver. The range is rated at 300 feet but many times it can exceed this.
Learn Button Programming: Simply press the learn button on the receiver. A light comes on. Then press the button on the remote you wish to use and the light blinks and turns off. Done! Repeat with other remotes or buttons. This receiver can learn up to 400 remotes
Versatility: Because of the simplicity of the receiver, it can be used to just about any purpose. On Estate Swings there is a second open command terminal for partial openings, you can use this receiver to allow a dual button remote to open your gate fully or partially. On Apollos and GTOs, there are open only terminals, you can use this receiver to create safer automation for multiple remote control users by only allowing them to open the gate and letting auto-close close the gate - great for condos and other public entrances so they cannot accidentally reverse the gate on another car. For any accessories that are not wireless you can use the 433UNIADP 433 MHz adapter paired up with this receiver to make it a wireless device. In addition to all that, it has both a normally open and normally closed connection, allowing it to either open a circuit or close a circuit wirelessly - we have had hundreds of customers that came up with many other great uses for this device.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have developed videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
433ESRec: Standard receiver - ready to wire into any system.
433ClipESRec12: Comes with plug in clip for ES 1000D and H gate openers
433ClipESRec12C: Comes with plug in clip for ES 300, ES 302, ES 500, ES 502, ES 400, ES 402, ES 1100, ES 1102, ESC 1102, ESL1200 gate openers
433ClipESRec24: Comes with plug in clip for ES 1600, ES 1602, ESC 1600, ESC 1602, ESU 2200, ESU 2202, ESL 1800, ESL2000 gate openers
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own automated gates, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
The Nice Apollo MOFB Moon Photocell detector prevents gates from closing on obstacles in its path. With the latest in photocell technology, the Blue Bus communication system reveals obstacles situated on the optical axis between the transmitter and receiver. These safety components ensure children, pets, and other objects stay out of harm's way.
This advanced gate safety system is easily installed with a mere two wires, and maintenance is minimal. These photocells do not require any special work aside from checking them once every six months to evaluate their condition. The units are vertically wall-mounted.
Specifications:
Product Type
The MOFB photocell detector is for gate and door automation systems (type D according to EN standard 12453), consisting in a “TX” transmitter and “RX” receiver.
Compatibility
Works with 936 and 1050 Control Boards.
Technology Employed
TX-RX direct optical interpolation with modulated infrared ray.
Power Supply/Output
The device can only be connected to “Blue Bus” networks, from which it receives its power supply and sends output signals.
Detection Capacity
Opaque objects (larger than 50 mm) located on the optical axis between TX and RX, which move more slowly than 1.6m/s.
TX Transmission Angle
20° +/- 25%
RX Reception Angle
Approximately 20°
Useful Range
Up to 15m for a maximum TX-RX misalignment of ± 5°. The device can detect and signal an obstacle even in particularly bad weather conditions.
Maximum Range, Under Optimum Conditions
Up to 30m for a maximum TX-RX misalignment of ± 5°.
Maximum Cable Length
Up to 50.
Addressing Possibility
Up to 7 detectors with the protection function, and 2 with the opening command function. The automatic synching prevents any interference among the various detectors.
The NIR-50-325 Retroreflective Photo Eye can be used as a reversing sensor for any assortment of gates. Its benefits include an extended range for improved performance in rain and snow. It has NC and 10k monitoring. A compact design that allows for easier mounting. A lower current draw that makes it superb for solar and low voltage applications. It comes in a weatherproof casing and is also UL325-2016 compliant for safety devices.
These features make the EMX NIR-50-325 the perfect photo eye for any gate setup.
-Estimated Radio Range: 0.5 ft (0.1 m) to 50 ft (15.2 m)
-Power Supply: 12…30VDC, 24…30VAC @ 60 Hz
-Protection class (IP): CE, UL325-2018
-Relay range: Up to 50 ft.
-Operating Temperature (°C Min/Max): -4° to 131°F (-20° to 55°C)
-Dimensions: L-1.3” (33mm) x W-0.8” (21mm) x H-2.6” (66mm)
-Weight: 0.2 lbs (91g)
-Warranty: “EMX Industries, Inc. products have a warranty against defects in materials and workmanship for a period of two years from date of sale to our customer.”
**Compatible with many operators such as: Patriot, Sentry, and Apollo gate openers.
GateCrafters.com offers more expert assistance than anyone.
If you need help deciding if this gate opener has the abilities that are right for your gate we have live application specialists available 9am - 9 pm EST 7 days a week or try our exclusive gate opener recommendation tool 24 hours/day.
EMX Industries is a manufacturer leading the industry in a wide range of sensor and control applications. Their access control and detection devices are equipped with technologies that sense general motion such as objects, vehicles, and people. Made in the USA, solutions from EMX are engineered and manufactured in Cleveland, Ohio. Participating in the DASMA committee on UL325 specifications, this trusted source stays focused on safety by adhering to their quality control system which promises only the highest quality and performance from their products.
The EMX NIR-50-325 is the upgraded version of the NIR-50. This model is the perfect installation to remain within compliance of UL 325 standards for automatic operation systems. This feature is the major difference between this new upgraded model and the previous version. Classified as an external entrapment device, this retro-reflective photo eye is used as a type B1 non contact sensor for safety and protection. UL325 requires continuous monitoring of all safety devices that are to be connected to a gate or door opener. Class I and II gate openers must have a safety audio alarm functioning properly at all times to protect any object in the activation area of the sensor.
The NIR-50-325 photo eye is an accessory part for a gate system that is configured for normally closed systems. It is meant to be installed alongside a new or already existing gate system. A red LED indicator provides assistance to technicians when aligning the photo eye with the reflector during installation. A yellow LED is used as the signal stability indicator between the sensors. Once the photo eye is installed, the reflective technology directs an infrared beam to the reflector and back to the photo eye again communicating any obstruction in range with a response time of 10ms. UL325 requires continuous monitoring of all safety devices that are to be connected to a gate or door opener. Each gate application requires its own unique monitoring method and it is advised to read the instruction manual from the manufacturer for your particular application. This retro-reflective photo eye equipped with extended range of 50 ft. and was designed to be used with gate operators, overhead garage doors, and other parking barriers.
Made from strong, rigid ABS plastics the enclosure provides complete structural integrity from resistance and force. With an environmental protection rating of IP66 this code indicates how tight the mechanical housing is against water and dust. This ingress protection rating indicates the sealing effectiveness which was designed to be effective against various weather conditions. EXM manufacturer warranty protects from defects and workmanship for up to 2 years of purchase.
GateCrafters.com has the resources you need.
How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question.
We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
GateCrafters.com is the DIY factor.
GateCrafters.com further adds to most of our gate openers for easier DIY installation.
We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener.
In addition we have the largest staff of factory trained technicians in the US.
The following tools and supplies are suggested in the manufacturer manual for optimal installation. They are not provided by Gate Crafters, however, most tools
are available at local hardware stores for purchase or rental.
Please refer to manual for Tools Needed.
Depending on the type of gate, power supply and contributing environmental factors additional tools or supplies may be needed. Please review the product manual associated with this gate opener model for further details.
Words from Senior Application Engineer, Anthony Geato
GateCrafters.com has actual experience.
We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories.
All these factors are what have lead to us having so many exclusive additions.
When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
