The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) is compatible wired with: All gate openers for 24-volt gate openers a 12-volt transformer will be needed (not included)
GateCrafters.com offers more expert assistance than anyone. We have live application specialists available 9 am - 9 pm EST 7 days a week.
The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) has the ability to control two separate devices or two different relays on a control board and can learn up to 400 codes. The typical situation for the receiver controlling two devices in a 3 car garage. Usually, there are 2 separate garage door openers in this type of garage and you can utilize the one receiver to control each one of them with a separate button on the remote. Another option for using the two relays on the receiver is controlling two separate terminals on a single gate opener. Many times gate openers will have a terminal for an automated open and close and another terminal for partial opening or open only during re-closing without stopping. A second button on the remote could be used to control this second function.
This receiver is also a plug-in receiver for Estate Swing gate openers. Please see the drop-down options.
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition, we have the largest staff of factory trained technicians in the US.
Easy Wiring: There are 4 or 6 wires that you need to connect depending on if you are using 1 or 2 channels. Two are for power, which can be AC or DC 12-24V. If you cannot find a power source (most gate openers have a battery you can run it off of) then you can hook it up to a transformer. (Search your junk drawers, many old transformers from other electronics may fall within the generous range allowed by our receiver). The other two wires close a circuit. On a garage door simply find the two terminals that the wall mount button uses.
Strong Range: This is one of the best features of this receiver. The range is rated at 300 feet but many times it can exceed this.
Learn Button Programming: Simply press the learn button on the receiver. A light comes on. Then press the button on the remote you wish to use and the light blinks and turns off. Done! Repeat with other remotes or buttons. This receiver can learn up to 400 remotes
Versatility: Because of the simplicity of the receiver, it can be used to just about any purpose. On Estate Swings there is a second open command terminal for partial openings, you can use this receiver to allow a dual button remote to open your gate fully or partially. On Apollos and GTOs, there are open only terminals, you can use this receiver to create safer automation for multiple remote control users by only allowing them to open the gate and letting auto-close close the gate - great for condos and other public entrances so they cannot accidentally reverse the gate on another car. For any accessories that are not wireless you can use the 433UNIADP 433 MHz adapter paired up with this receiver to make it a wireless device. In addition to all that, it has both a normally open and normally closed connection, allowing it to either open a circuit or close a circuit wirelessly - we have had hundreds of customers that came up with many other great uses for this device.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have developed videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
433ESRec: Standard receiver - ready to wire into any system.
433ClipESRec12: Comes with plug in clip for ES 1000D and H gate openers
433ClipESRec12C: Comes with plug in clip for ES 300, ES 302, ES 500, ES 502, ES 400, ES 402, ES 1100, ES 1102, ESC 1102, ESL1200 gate openers
433ClipESRec24: Comes with plug in clip for ES 1600, ES 1602, ESC 1600, ESC 1602, ESU 2200, ESU 2202, ESL 1800, ESL2000 gate openers
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own automated gates, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
Apollo: 1500, 1600, 1550, 1650, 3500ETL, 3600ETL, 7000UL, 7500ETL, BA-12 (must be equipped with the Estate Swing 433ESREC Transmitter)
Other: Estate Swing 433 MHz Receiver wired into any other device.
Note: If you use the Estate Swing 433ESREC transmitter, then this keypad WILL be compatible. You must use the 433ESREC transmitter in your system in order to use this keypad.
Gate Crafters offers more expert assistance than anyone. If you need help deciding if this gate opener has the abilities that are right for your gate we have live application specialists available 9am - 9 pm EST 7 days a week or try our exclusive gate opener recommendation tool 24 hours/day.
The Estate Swing wireless 4-channel digital keypad is a must-have for every gate opener. It can store 4 access codes, each sending a uniquely coded signal. This is important because each code can independently control its own device, or all 4 can control the same gate. Use the codes for family, friends, lawn services, deliveries, etc., or assign them to the gate, pedestrian gate, garage, or daytime-only access.
Some possibilities are as follows:
Each Estate Swing receiver comes with two channels. The first channel is used by the gate opener to open and close the gate; the second channel is available for other uses. For example, if you purchase a timer, you could wire the second channel to the timer and have that channel active only during business hours. You can program one access code to trigger channel 1 and open the gate at any time, while programming a second code for channel 2 to allow access only during business hours.
If your garage is within 200 feet of your gate, you could add an Estate Swing receiver to the garage door opener. Then, you could program one access code for the gate and another for the garage door.
If you have a pedestrian gate with an electric lock, you could add an Estate Swing receiver to the lock kit. This would allow you to release the lock through the same keypad as the gate opener.
Alternatively, you can program multiple codes to the receiver that comes with your Estate Swing. Keep one code for family members, which you know will never need to change, and use the other codes for deliveries or lawn services. If you need to change one of them, your family members won’t need to memorize a new code.
During night hours, after a key is pressed, the keypad illuminates with a bright yet attractive blue LED. The LED will remain lit while the keypad is in use, then turn off to conserve battery power.
An additional popular feature is the single-digit secondary transmission. After entering an access code, you can press any numerical key on the keypad within approximately 20 seconds to send a second signal. This is useful if you need to stop or reverse the gate because it is about to hit an obstacle.
The residential keypad housing is made of UV-protected black ABS plastic. The buttons on the residential version are backlit in white when pressed. The keypad housing is constructed from hardened polymer and has a matte black finish. The keypad is surface-lit by a blue LED light when a key is pressed. Both versions are designed for easy mounting and blend well aesthetically with a keypad stand or can be surface-mounted to a column, fence, or garage door frame. They are completely weatherproof and require no hood or cover to protect them from the elements.
4 Channels: Control up to four devices with a single keypad
Long range: 200+ foot wireless signal
Night Use: Keypad LED illuminates when numbers are pressed
Battery Powered: Requires a 9V battery (lithium battery recommended) not included
Secure: Locked to mounting plate, requires specialized provided tool for removal
Gate Crafters has the resources you need. How do you use your gate opener system once you get it? Gate Crafters is the only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
Words from Senior Application Engineer, Anthony Gaeto
“The Estate Swing 433MHz 4-Channel keypad, comes with your choice of housing. This keypad has the capability to be learned wireless with an Estate Swing 433MHz receiver. The receiver has two separate channels built in. The first channel controls the opening and closing of your gate opener, and the second channel can be in conjunction with a timer to give codes that are only able to operate the gate opener during business hours or other time parameters. The residential housing features a ABS black plastic body that is UV protected, which will keep this keypad looking great for years to come. The keys on this keypad are lit by upper LED and will come on once a key is pressed. The Residential grade housing is made of all metal and features a stainless steel faceplate as well as stainless steel buttons.
This unit features a built in LED bulb that will illuminate the keys during use. One nice feature of the Estate Swing keypads, is the capability of being able to send a secondary digit transmission to the receiver. After you enter your entry code, you will be allowed to press a single numerical key to either stop or reverse your gate. This window lasts for 20 seconds for a secondary transmission. This is helpful in the case that someone enters the path of the driveway gate. If you need any help with the programming of your Estate Swing keypad, please watch this video or give us a call, send us a email, or use our live chat. Gate Crafters has experts standing by to help you out with any question you may have. We are available 7 days a week from 9 am to 9 pm, eastern time. We look forward to hearing from you”
For over a decade, Gate Crafters has been the premier online retailer of gate openers and accessories. With our extensive technical and installation expertise, we are authorized to serve the DIY market. We believe customers should have the opportunity to take pride in their projects, whether installing or troubleshooting a gate opener. Everyone deserves the option to enjoy high-quality products without the need to hire help.
At Gate Crafters, we empower you to install confidently by providing access to our trained technical staff seven days a week from 9 AM to 9 PM EST. By choosing to DIY your gate opener system, you can save thousands of dollars over its lifetime while gaining valuable knowledge about your installation and how the system operates. This understanding will make it easier to troubleshoot any issues and perform routine maintenance in the future.
Gate Crafters is the DIY factor. Gate Crafters further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians in the US.
Order specific customized accessory wiring instructions
360 degree accessories - we can take you through exit, entry, safety, power, and all other minute details to create a fully rounded kit.
Free 24/7/365 Installation Support
Free 7 day/week Technical Support
Largest Number of Certified Techs in America
Free assistance to find the right gate opener for your gate
Free systems design assistance to match the right accessories to fit your needs.
Extremely competitive pricing
Free shipping on all accessories purchased with a gate opener
We stock replacement parts
Many brands of many types of accessories, enough to handle just about any operational situation you can imagine
Gate Crafters has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
The UltraIIDTEK™ vehicle loop detector is compatible with most gate operators. The UltraIIDTEK™ may be used in Center, Safety, and Exit loop positions. The UltraMETER™ display feature makes setup easy by displaying the optimum sensitivity setting required to detect a vehicle positioned on the loop. Ten sensitivity settings allow for fine adjustment of detection level. A PULSE/PRESENCE switch allows configuration of output relay for presence or one second pulse on entry operation. Four frequency settings provide flexibility in preventing crosstalk in multi-loop applications.
Sensitivity: 10 levels, 0-9
UltraMETER™ Display: Indicates optimum sensitivity level, 0-9 diagnostic aid
Loop Frequency: 4 settings
Loop inductance: 20 - 200μH
Grounded Loop: Isolation transformer allows operation with poor quality loops
Automatic Tuning: Detector tunes to loop on power-up and following frequency count function
Environmental Tracking: Automatic compensation
Surge Protection: Loop circuitry protected by surge suppressors.
Detect Output: COM, NO and NC contacts
Power / loop fault indicator: Green LED
Detect / frequency count indicator: Red LED
ASB (Automatic Sensitivity Boost): Increases sensitivity after initial detection to prevent dropout due to high-bed vehicles
Relay Operation: Presence or one-second pulse on entry
Dimensions: 3" length x 0.9" width x 2 3/4" height
Weight: 0.15 lbs
Connector: 7 position male
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We
have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of
accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians
in the US.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the
only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write
DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
Words from Senior Application Engineer, Anthony Gaeto
“We are always getting questions about how gate exit wands work and how they are different from exit loops.
Exit wands are what is know as a magnetometer which senses changes in the Earth’s magnetic field. An easy way to explain how exit wands work is to picture a boat traveling through the water. As the boat is traveling it is creating waves. As your car travels through the magnetic field of the Earth it creates similar waves, like the boat. The exit wand’s magnetometer picks up on these waves as you travel by the wand. One downside of exit wands is that they do loose sight of your vehicle when it is stopped.
Gate Crafters carries 5 different types of exit wands that work very similar to each other. The only difference between these wands are some of their features. The GTO/PRO wireless exit wand is wireless between the magnetometer and receiver. The Gate Crafters exit wand is manufactured by EMX and has been around for years. The GTO exit wand is recommend for use with other GTO openers and accessories. The Estate Swing exit wand does come with a range control board that allow you to adjust the sensitivity of the magnetometer. This feature allows you tune down the range of the exit wand, so that vehicles such as a lawn mower doesn’t set open your gate, but this isn’t a complete failsafe, as it will still operate the gate opener when something is nearby. The Estate Swing Deluxe Exit wand is the most different from the other exit wands. It is constructed out of copper and features a ground cable that attach to a grounding rod that helps protect this exit wand from lightning strikes. The other 4 exit wands do not have this feature and are susceptible to damage from lightning strikes. Also the Estate Swing Deluxe Exit Wand comes with a 5 year warranty, which is longer than any other exit wand we sell.
Exit loops differ from exit wands in that they are buried in the driveway in a loop and are wire to the gate opener. The way exit loops work is that they detect the presence of metal (your car) above the loop. It does not matter if your car is moving or not, the loop will detect the car. Besides being used to exit your property, exit loops are used for safety. When exit loops are used a safety device, they will prevent your gate from closing on your car, when it detect a car nearby to your gate. The exit loop is wired to a exit loop detector, which is then wired into your gate opener’s control board.
GateCrafters.com is a one stop shop for gate openers and gate accessories at a great price. Gate Crafters was started on the idea of providing gate opener and accessories along with great customer service to our valued customers. We have technical support available to you 7 days a week from 9 am to 9 pm, eastern time. Our experts are standing by to take your phone call, answer your email, or chat with you with our live chat on our website. We welcome any question you may have and can help you put together a complete package for you so your gate operates how you want it to. We look forward to hearing from you."
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and
have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we
pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you
see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on
these ideas and have utilized them to help thousands of customers automate their gates.
The Diablo Controls Safety Loop Detector (DSP-6LP) has been specifically designed for solar powered gate applications. This detector will operate on any voltage from 10 to 30 volts AC or DC and draws less than 2 milliamperes while waiting for a car. The power LED blinks continuously once per second to indicate the detector is operating in the low power and fail secure mode.
The detector's small size and lack of any switches or dials, becomes the industry's first solar powered "Plug-and-Play" vehicle detector. The Diablo Controls Safety Loop Detector is preset to the normal sensitivity level used in parking/access control applications, and tunes itself to the best operating frequency. This micro-sized detector will automatically adjust its sensitivity level when used on different sized loops. Environmental conditions are constantly compensated with the Diablo Controls Safety Loop Detector HYPERTRACK software. Diablo Controls Safety Loop Detector 's inherent noise filtering algorithms allow it to work reliably in any electrical situation.
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians in the US.
Loop size: Works on any in-ground inductive loop from 20 to 1200 uH.
Indicators: Separate Power and Detect LED's. The green and Power LED will blink continuously under normal operation. The red Detect LED will turn solid for a vehicle.
Connector: Easy terminal connections with removable 7-pin terminal block.
Sensitivity: Automatic which compensates for large loops or large wire lead-ins.
Output Ratings: Single output, 1 amp relay at 30 VDC Resistive, with relay common, N/O, and N/C contacts are available.
Loop Failure: The green power indicator flashes slowly if the circuit is open and quickly if the loop circuit is shorted. This detector operates in fail secure mode and will not output a "Detect" for either of these loop failed conditions.
Power: 10 to 30 volts AC or DC, with approximately 1.5mA (no car and all loop sizes) and less than 25mA with a car on the loop perfect for solar applications.
Size: Small compact design allows the controller to fit in almost all control boxes. 1.52"H x 2.9"W x 1.56"D
Operating Temperature: -35 to 165 degrees Fahrenheit
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
Words from Senior Application Engineer, Anthony Gaeto
“We are always getting questions about how gate exit wands work and how they are different from exit loops.
Exit wands are what is know as a magnetometer which senses changes in the Earth’s magnetic field. An easy way to explain how exit wands work is to picture a boat traveling through the water. As the boat is traveling it is creating waves. As your car travels through the magnetic field of the Earth it creates similar waves, like the boat. The exit wand’s magnetometer picks up on these waves as you travel by the wand. One downside of exit wands is that they do loose sight of your vehicle when it is stopped.
Gate Crafters carries 5 different types of exit wands that work very similar to each other. The only difference between these wands are some of their features. The GTO/PRO wireless exit wand is wireless between the magnetometer and receiver. The Gate Crafters exit wand is manufactured by EMX and has been around for years. The GTO exit wand is recommend for use with other GTO openers and accessories. The Estate Swing exit wand does come with a range control board that allow you to adjust the sensitivity of the magnetometer. This feature allows you tune down the range of the exit wand, so that vehicles such as a lawn mower doesn’t set open your gate, but this isn’t a complete failsafe, as it will still operate the gate opener when something is nearby. The Estate Swing Deluxe Exit wand is the most different from the other exit wands. It is constructed out of copper and features a ground cable that attach to a grounding rod that helps protect this exit wand from lightning strikes. The other 4 exit wands do not have this feature and are susceptible to damage from lightning strikes. Also the Estate Swing Deluxe Exit Wand comes with a 5 year warranty, which is longer than any other exit wand we sell.
Exit loops differ from exit wands in that they are buried in the driveway in a loop and are wire to the gate opener. The way exit loops work is that they detect the presence of metal (your car) above the loop. It does not matter if your car is moving or not, the loop will detect the car. Besides being used to exit your property, exit loops are used for safety. When exit loops are used a safety device, they will prevent your gate from closing on your car, when it detect a car nearby to your gate. The exit loop is wired to a exit loop detector, which is then wired into your gate opener’s control board.
GateCrafters.com is a one stop shop for gate openers and gate accessories at a great price. Gate Crafters was started on the idea of providing gate opener and accessories along with great customer service to our valued customers. We have technical support available to you 7 days a week from 9 am to 9 pm, eastern time. Our experts are standing by to take your phone call, answer your email, or chat with you with our live chat on our website. We welcome any question you may have and can help you put together a complete package for you so your gate operates how you want it to. We look forward to hearing from you.
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
“The Estate Swing 433MHz 4-Channel keypad, comes with your choice of housing. This keypad has the capability to be learned wireless with an Estate Swing 433MHz receiver. The receiver has two separate channels built in. The first channel controls the opening and closing of your gate opener, and the second channel can be in conjunction with a timer to give codes that are only able to operate the gate opener during business hours or other time parameters. The residential housing features a ABS black plastic body that is UV protected, which will keep this keypad looking great for years to come. The keys on this keypad are lit by upper LED and will come on once a key is pressed. The Residential grade housing is made of all metal and features a stainless steel faceplate as well as stainless steel buttons.
