The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) is compatible wired with: All gate openers for 24-volt gate openers a 12-volt transformer will be needed (not included)
GateCrafters.com offers more expert assistance than anyone. We have live application specialists available 9 am - 9 pm EST 7 days a week.
The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) has the ability to control two separate devices or two different relays on a control board and can learn up to 400 codes. The typical situation for the receiver controlling two devices in a 3 car garage. Usually, there are 2 separate garage door openers in this type of garage and you can utilize the one receiver to control each one of them with a separate button on the remote. Another option for using the two relays on the receiver is controlling two separate terminals on a single gate opener. Many times gate openers will have a terminal for an automated open and close and another terminal for partial opening or open only during re-closing without stopping. A second button on the remote could be used to control this second function.
This receiver is also a plug-in receiver for Estate Swing gate openers. Please see the drop-down options.
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition, we have the largest staff of factory trained technicians in the US.
Easy Wiring: There are 4 or 6 wires that you need to connect depending on if you are using 1 or 2 channels. Two are for power, which can be AC or DC 12-24V. If you cannot find a power source (most gate openers have a battery you can run it off of) then you can hook it up to a transformer. (Search your junk drawers, many old transformers from other electronics may fall within the generous range allowed by our receiver). The other two wires close a circuit. On a garage door simply find the two terminals that the wall mount button uses.
Strong Range: This is one of the best features of this receiver. The range is rated at 300 feet but many times it can exceed this.
Learn Button Programming: Simply press the learn button on the receiver. A light comes on. Then press the button on the remote you wish to use and the light blinks and turns off. Done! Repeat with other remotes or buttons. This receiver can learn up to 400 remotes
Versatility: Because of the simplicity of the receiver, it can be used to just about any purpose. On Estate Swings there is a second open command terminal for partial openings, you can use this receiver to allow a dual button remote to open your gate fully or partially. On Apollos and GTOs, there are open only terminals, you can use this receiver to create safer automation for multiple remote control users by only allowing them to open the gate and letting auto-close close the gate - great for condos and other public entrances so they cannot accidentally reverse the gate on another car. For any accessories that are not wireless you can use the 433UNIADP 433 MHz adapter paired up with this receiver to make it a wireless device. In addition to all that, it has both a normally open and normally closed connection, allowing it to either open a circuit or close a circuit wirelessly - we have had hundreds of customers that came up with many other great uses for this device.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have developed videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
433ESRec: Standard receiver - ready to wire into any system.
433ClipESRec12: Comes with plug in clip for ES 1000D and H gate openers
433ClipESRec12C: Comes with plug in clip for ES 300, ES 302, ES 500, ES 502, ES 400, ES 402, ES 1100, ES 1102, ESC 1102, ESL1200 gate openers
433ClipESRec24: Comes with plug in clip for ES 1600, ES 1602, ESC 1600, ESC 1602, ESU 2200, ESU 2202, ESL 1800, ESL2000 gate openers
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own automated gates, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
The Gate Crafters sensor is a multipurpose exit sensor and vehicle detector that allows hands free access; and, because of its simple design, it is compatible with most gate openers including the Estate Swing, Apollo, Zareba, and many others. The single piece design provides the installer with a simple installation procedure. The Gate Crafters Exit Sensor is buried in the ground so a potential intruder or vandals do not notice it. The Gate Crafters have a wide range of power supply options from 9V to 41V AC or DC. Low current consumption makes it an excellent choice for solar power applications.
The Gate Crafters sensor uses a passive probe sensor to detect changes in the earth's magnetic field. These changes are caused by a movement of ferrous metal objects such as a car in the proximity of the probe. The sensing area of each probe is in the shape of about 15-foot circle. The size of this detection circle changes with the size and speed of the moving car. The Gate Crafters sensor can be buried in the ground about 6 inches deep parallel to the paved driveway. It also can be placed 2 inches deep in asphalt or concrete under the path of the vehicle.
Note: Exit wands/sensors should not be used on properties in which the driveway gate is designed to keep in pets, children or livestock due to the possibility for unintentional openings. Our suggestion is to use a keypad for exiting so the gate will only open when it is intended to by code.
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition, we have the largest staff of factory trained technicians in the US.
Access Control: Can be used as a free exit vehicle detector for gates, overhead doors, and parking barriers.
Safety: Can be used to detect moving vehicles in an environment where there are blind areas along the driving path and actuates warning lights.
Energy Conservation: Can be used to detect moving vehicles along a driving path or driveway and turn lights on only in the proximity of the vehicle.
Security: Can be used to detect approaching vehicles or an unauthorized movement of a parked vehicle and actuate alarms, video cameras or vehicle annunciators.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have developed videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
The exit wand is available with the following amount of lead wire. You may not extend the wire. Choose your desired option above.
50' Lead Wire
100' Lead Wire
150' Lead Wire
200' Lead Wire
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own automated gates, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
Use this formula to calculate how far from the gate the loops should be placed so that by the time a car reaches the gate, the gate will be completely open:
Exit Loop formula: x*(y*1.46)=z
x = time for gate to open in seconds.
y = Desired MPH to reach gate.
z = how far from gate.
FYI - 1.46 converts miles per hour to feet per second. We also recommend adding in 10 to 20 feet so the gate is fully open at a comfortable distance
from the
gate.
For placement of a safety loop before and after the gate use the formula below. A safety loop is designed to stop the motion of the gate before the
car reaches
the gate. The distance below should give an ample amount of time for the gate to stop before hitting a vehicle:
Safety Formula: 4 feet before a closed gate and after an opened gate.
Words from Senior Application Engineer, Anthony Gaeto
“We are always getting questions about how gate exit wands work and how they are different from exit loops.
Exit wands are what is know as a magnetometer which senses changes in the Earth’s magnetic field. An easy way to explain how exit wands work is to picture a boat traveling through the water. As the boat is traveling it is creating waves. As your car travels through the magnetic field of the Earth it creates similar waves, like the boat. The exit wand’s magnetometer picks up on these waves as you travel by the wand. One downside of exit wands is that they do lose sight of your vehicle when it is stopped.
Gate Crafters carries 5 different types of exit wands that work very similar to each other. The only difference between these wands is some of their features. The GTO/PRO wireless exit wand is wireless between the magnetometer and receiver. The Gate Crafters exit wand is manufactured by EMX and has been around for years. The GTO exit wand is recommended for use with other GTO openers and accessories. The Estate Swing exit wand does come with a range control board that allows you to adjust the sensitivity of the magnetometer. This feature allows you tune down the range of the exit wand so that vehicles such as a lawnmower don’t set open your gate, but this isn’t a complete failsafe, as it will still operate the gate opener when something is nearby. The Estate Swing Deluxe Exit wand is the most different from the other exit wands. It is constructed out of copper and features a ground cable that attaches to a grounding rod that helps protect this exit wand from lightning strikes. The other 4 exit wands do not have this feature and are susceptible to damage from lightning strikes. Also, the Estate Swing Deluxe Exit Wand comes with a 5 year warranty, which is longer than any other exit wand we sell.
Exit loops differ from exit wands in that they are buried in the driveway in a loop and are wire to the gate opener. The way exit loops work is that they detect the presence of metal (your car) above the loop. It does not matter if your car is moving or not, the loop will detect the car. Besides being used to exit your property, exit loops are used for safety. When exit loops are used as a safety device, they will prevent your gate from closing on your car, when they detect a car nearby to your gate. The exit loop is wired to an exit loop detector, which is then wired into your gate opener’s control board.
GateCrafters.com is a one stop shop for gate openers and gate accessories at a great price. Gate Crafters was started on the idea of providing gate openers and accessories along with great customer service to our valued customers. We have technical support available to you 7 days a week from 9 am to 9 pm, eastern time. Our experts are standing by to take your phone call, answer your email, or chat with you with our live chat on our website. We welcome any question you may have and can help you put together a complete package for you so your gate operates how you want it to. We look forward to hearing from you.
Unlighted button for entry or exit. Connects directly to the control board using 16 gauge stranded, low voltage, direct burial wire (not included).
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians in the US.
Outdoor Use: can be wired into an area unprotected from weather
Simple: simple 2 wire installation
Low cost: add as many as needed to activate your gate from multiple locations
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
GateCrafters.com brings a special product to gate opener accessories – a Universal Digital Gate Timer. With this compact timer unit, home and business owners will be able to control
when their gate opens and closes. With several exciting features and functionalities you’ll finally be able to get the ultimate in accessibility and security that you seek out of your driveway
gate. This timer has universal application due to its 12 or 24 volt operation it can function with almost every gate opener on the market. Mount inside home/business, in a gate opener
control box or outdoor rated electrical box.
Controlled Open/Close
You can open and close your gate at a particular time with the gate timer via a programming sequence which allows you to open at a preset time and close at a preset time. The timer
allows for this to be either: weekday only, 7-days a week, single day or a combination of the three.
Inactive Accessories Function
You can make accessories like automatic entry or exit through loop or auto-sensor inactive during “off” hours. For example during evening hours some users wish to have automatic
access off to create a more secure environment. With the Universal Digital Gate Timer you can achieve this secure "off" hours setting.
Manager Opening / Auto-Reclose
This setting allows a manager to open the gate at a particular time with the gate remaining open until a preset auto-close time. Have the gate open only after an authorized individual has
activated the gate but subsequently after close at a particular time. This function works great for commercial establishments like lumber yards or car lot.
Complete Gate Lockout Times
Use this function of the timer to make the gate opener access completely disabled during off hours without shutting down the system and possibly losing programming. During evening
hours some users wish to have all access off limits through a particular gate, such as an auxiliary gate. It has built-in security because it programs the gate to not reopen at a certain period
of time but still close if already opened.
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example:
easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition we have
the largest staff of factory trained technicians in the US.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this
question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each
accessory to be installed with each gate opener.
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we
attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us
having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on
these ideas and have utilized them to help thousands of customers automate their gates.
A giant leap forward in gate opener technology! The Nice/Apollo 1050 control board is built to make your life easier, at least when it comes to worry free driveway gate access. This control board can be used with the following gate openers:
Apollo 1550
Apollo 1650
Apollo 3500
Apollo 3600
Apollo NT-T5
Apollo NT-T7
NT-M12ETL
NT-H12ETL
Apollo 7200
Apollo 7300
Why add this board to your Apollo order?
This board has some amazing features. It has a built in multi-meter to tell you your battery voltage, transformer voltage, and amperage pull of your motors for diagnostics. It has full range of speed adjustment to control how fast the motors open, close, and soft stop. It is a DIY friendly board that won’t allow you to make mistakes such as reversing polarity - it simply indicates with a red light your polarity is wrong and you can then correct it. The board has clear markings for all the terminals and the settings are all done digitally by display with actual words to indicate what function you are performing, not just codes and numbers.
**US version must be used with monitored photo eyes.
At Gate Crafters we are committed to providing easy to understand content to eliminate confusion when purchasing a product. We cut through the version confusion to help you find the correct replacement part for your needs. Since we, like most other suppliers, do NOT allow for returns of electronic parts, we go the extra step to to make sure you get the correct product for your project. The parts we sell are designed to work with all gate openers of the specific generation. CAUTION: Not all boards & parts sold online are 100% compatible even if they are the same generation, whereas our are GUARANTEED to be compatible with all versions of the indicated generation.
