The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) is compatible wired with: All gate openers for 24-volt gate openers a 12-volt transformer will be needed (not included)
GateCrafters.com offers more expert assistance than anyone. We have live application specialists available 9 am - 9 pm EST 7 days a week.
The Estate Swing 433 MHz 2 Channel Receiver (433ESREC) has the ability to control two separate devices or two different relays on a control board and can learn up to 400 codes. The typical situation for the receiver controlling two devices in a 3 car garage. Usually, there are 2 separate garage door openers in this type of garage and you can utilize the one receiver to control each one of them with a separate button on the remote. Another option for using the two relays on the receiver is controlling two separate terminals on a single gate opener. Many times gate openers will have a terminal for an automated open and close and another terminal for partial opening or open only during re-closing without stopping. A second button on the remote could be used to control this second function.
This receiver is also a plug-in receiver for Estate Swing gate openers. Please see the drop-down options.
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition, we have the largest staff of factory trained technicians in the US.
Easy Wiring: There are 4 or 6 wires that you need to connect depending on if you are using 1 or 2 channels. Two are for power, which can be AC or DC 12-24V. If you cannot find a power source (most gate openers have a battery you can run it off of) then you can hook it up to a transformer. (Search your junk drawers, many old transformers from other electronics may fall within the generous range allowed by our receiver). The other two wires close a circuit. On a garage door simply find the two terminals that the wall mount button uses.
Strong Range: This is one of the best features of this receiver. The range is rated at 300 feet but many times it can exceed this.
Learn Button Programming: Simply press the learn button on the receiver. A light comes on. Then press the button on the remote you wish to use and the light blinks and turns off. Done! Repeat with other remotes or buttons. This receiver can learn up to 400 remotes
Versatility: Because of the simplicity of the receiver, it can be used to just about any purpose. On Estate Swings there is a second open command terminal for partial openings, you can use this receiver to allow a dual button remote to open your gate fully or partially. On Apollos and GTOs, there are open only terminals, you can use this receiver to create safer automation for multiple remote control users by only allowing them to open the gate and letting auto-close close the gate - great for condos and other public entrances so they cannot accidentally reverse the gate on another car. For any accessories that are not wireless you can use the 433UNIADP 433 MHz adapter paired up with this receiver to make it a wireless device. In addition to all that, it has both a normally open and normally closed connection, allowing it to either open a circuit or close a circuit wirelessly - we have had hundreds of customers that came up with many other great uses for this device.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have developed videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
433ESRec: Standard receiver - ready to wire into any system.
433ClipESRec12: Comes with plug in clip for ES 1000D and H gate openers
433ClipESRec12C: Comes with plug in clip for ES 300, ES 302, ES 500, ES 502, ES 400, ES 402, ES 1100, ES 1102, ESC 1102, ESL1200 gate openers
433ClipESRec24: Comes with plug in clip for ES 1600, ES 1602, ESC 1600, ESC 1602, ESU 2200, ESU 2202, ESL 1800, ESL2000 gate openers
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own automated gates, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
This unit is a complete solar alternative kit. Complete with stand and wire, this kit replaces the need for a 110v connection. The solar panel trickle charges the battery the same as the 110v connection. It is perfect for remote locations, long driveways, or energy conservative individuals. Solar energy is the cleanest, safest form of power available; using the sun for energy benefits the environment as well as your wallet and eliminates the concern of power outages.
The solar panel is completely weatherproof and virtually indestructible. Estate Swing's non-glass solar panels feature a clear front covering and are mounted to an anodized aluminum frame. The heart of the solar panel is the collection of solar cells, which optimizes the amount of energy absorbed even in low light situations. Each cell transforms the sunlight into energy through a photovoltaic process (converting photons into electrons). Working as a cohesive unit these cells can generate electricity that will work with solar compatible gate opener systems. As a rule of thumb; heavier gates and/or more frequent cycles (a cycle is defined as one open and closure) the more solar wattage you’ll need. Review your gate opener manual for information on which panel would best suit your needs.
*Make and model may vary from picture above.
Optimum Orientation for Solar Panels: (Your Latitude x 0.9) + 29 Degrees= # of degrees your panel should be angled towards true South from the horizontal position (laying flat pointing directly up)
Gate Crafters is the DIY factor. Gate Crafters further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians in the US.
No Power Consumption: Environmentally beneficial - collects sun's energy and creates electricity
Outdoor ready: Weatherproof, ready to be used in all conditions
10 Year Warranty: Comes with a standard 10 year warranty
Gate Crafters has the resources you need. How do you use your gate opener system once you get it? Gate Crafters is the only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
Gate Crafters has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
Unlighted button for entry or exit. Connects directly to the control board using 16 gauge stranded, low voltage, direct burial wire (not included).
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians in the US.
Outdoor Use: can be wired into an area unprotected from weather
Simple: simple 2 wire installation
Low cost: add as many as needed to activate your gate from multiple locations
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
The UltraIIDTEK™ vehicle loop detector is compatible with most gate operators. The UltraIIDTEK™ may be used in Center, Safety, and Exit loop positions. The UltraMETER™ display feature makes setup easy by displaying the optimum sensitivity setting required to detect a vehicle positioned on the loop. Ten sensitivity settings allow for fine adjustment of detection level. A PULSE/PRESENCE switch allows configuration of output relay for presence or one second pulse on entry operation. Four frequency settings provide flexibility in preventing crosstalk in multi-loop applications.
Sensitivity: 10 levels, 0-9
UltraMETER™ Display: Indicates optimum sensitivity level, 0-9 diagnostic aid
Loop Frequency: 4 settings
Loop inductance: 20 - 200μH
Grounded Loop: Isolation transformer allows operation with poor quality loops
Automatic Tuning: Detector tunes to loop on power-up and following frequency count function
Environmental Tracking: Automatic compensation
Surge Protection: Loop circuitry protected by surge suppressors.
Detect Output: COM, NO and NC contacts
Power / loop fault indicator: Green LED
Detect / frequency count indicator: Red LED
ASB (Automatic Sensitivity Boost): Increases sensitivity after initial detection to prevent dropout due to high-bed vehicles
Relay Operation: Presence or one-second pulse on entry
Dimensions: 3" length x 0.9" width x 2 3/4" height
Weight: 0.15 lbs
Connector: 7 position male
GateCrafters.com is the DIY factor. GateCrafters.com further adds to most of our gate openers for easier DIY installation. We
have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of
accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians
in the US.
GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the
only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write
DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
Words from Senior Application Engineer, Anthony Gaeto
“We are always getting questions about how gate exit wands work and how they are different from exit loops.
Exit wands are what is know as a magnetometer which senses changes in the Earth’s magnetic field. An easy way to explain how exit wands work is to picture a boat traveling through the water. As the boat is traveling it is creating waves. As your car travels through the magnetic field of the Earth it creates similar waves, like the boat. The exit wand’s magnetometer picks up on these waves as you travel by the wand. One downside of exit wands is that they do loose sight of your vehicle when it is stopped.
Gate Crafters carries 5 different types of exit wands that work very similar to each other. The only difference between these wands are some of their features. The GTO/PRO wireless exit wand is wireless between the magnetometer and receiver. The Gate Crafters exit wand is manufactured by EMX and has been around for years. The GTO exit wand is recommend for use with other GTO openers and accessories. The Estate Swing exit wand does come with a range control board that allow you to adjust the sensitivity of the magnetometer. This feature allows you tune down the range of the exit wand, so that vehicles such as a lawn mower doesn’t set open your gate, but this isn’t a complete failsafe, as it will still operate the gate opener when something is nearby. The Estate Swing Deluxe Exit wand is the most different from the other exit wands. It is constructed out of copper and features a ground cable that attach to a grounding rod that helps protect this exit wand from lightning strikes. The other 4 exit wands do not have this feature and are susceptible to damage from lightning strikes. Also the Estate Swing Deluxe Exit Wand comes with a 5 year warranty, which is longer than any other exit wand we sell.
Exit loops differ from exit wands in that they are buried in the driveway in a loop and are wire to the gate opener. The way exit loops work is that they detect the presence of metal (your car) above the loop. It does not matter if your car is moving or not, the loop will detect the car. Besides being used to exit your property, exit loops are used for safety. When exit loops are used a safety device, they will prevent your gate from closing on your car, when it detect a car nearby to your gate. The exit loop is wired to a exit loop detector, which is then wired into your gate opener’s control board.
GateCrafters.com is a one stop shop for gate openers and gate accessories at a great price. Gate Crafters was started on the idea of providing gate opener and accessories along with great customer service to our valued customers. We have technical support available to you 7 days a week from 9 am to 9 pm, eastern time. Our experts are standing by to take your phone call, answer your email, or chat with you with our live chat on our website. We welcome any question you may have and can help you put together a complete package for you so your gate operates how you want it to. We look forward to hearing from you."
GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and
have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we
pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you
see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on
these ideas and have utilized them to help thousands of customers automate their gates.
Gate Crafters 16 Gauge, 2 Conductor Wire (1000 ft. Roll)
The Gate Crafters conductor wire is ideal for connecting gate opener transformers or adding accessories to your system. It features durable double insulation, is UV-resistant, and can be directly buried in the ground. The wire is flexible, easy to strip, and handles bends without breaking, making installation hassle-free. Available in any quantity, this wire completes your installation kit with reliable, long-lasting performance.
Gate Crafters offers more expert assistance than anyone. If you need help deciding if this gate opener has the abilities that are right for your gate we have live application specialists available 9am - 9 pm EST 7 days a week or try our exclusive gate opener recommendation tool 24 hours/day.
Durable: This wire is double-insulated, UV-resistant, and can be directly buried in the ground.
Convenient: Available in any quantity at a great price, and can be delivered with your gate opener or accessory. It completes your gate opener kit and provides everything you need for installation.
Easy to work with: Some wire can be a pain to strip, too stiff to conform to necessary twists and turns, or prone to breaking after bending. This wire, however, can be bent repeatedly, easily shaped to your needs, and a standard pair of wire strippers makes preparation quick and easy.
Gate Crafters has the resources you need. How do you use your gate opener system once you get it? Gate Crafters is the only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.
For over a decade, Gate Crafters has been the premier online retailer of gate openers and accessories. With our extensive technical and installation expertise, we are authorized to serve the DIY market. We believe customers should have the opportunity to take pride in their projects, whether installing or troubleshooting a gate opener. Everyone deserves the option to enjoy high-quality products without the need to hire help.
At Gate Crafters, we empower you to install confidently by providing access to our trained technical staff seven days a week from 9 AM to 9 PM EST. By choosing to DIY your gate opener system, you can save thousands of dollars over its lifetime while gaining valuable knowledge about your installation and how the system operates. This understanding will make it easier to troubleshoot any issues and perform routine maintenance in the future.
Gate Crafters is the DIY factor. Gate Crafters further adds to most of our gate openers for easier DIY installation. We have developed exclusive components (example: easy adjustable mounting brackets), customized instructions, and offer a full spectrum of accessories to truly cover all aspects of the installation of your gate opener. In addition we have the largest staff of factory trained technicians in the US.
Order specific customized accessory wiring instructions
360 degree accessories - we can take you through exit, entry, safety, power, and all other minute details to create a fully rounded kit.
Free 24/7/365 Installation Support
Free 7 day/week Technical Support
Largest Number of Certified Techs in America
Free assistance to find the right gate opener for your gate
Free systems design assistance to match the right accessories to fit your needs.
Extremely competitive pricing
Free shipping on all accessories purchased with a gate opener
We stock replacement parts
Many brands of many types of accessories, enough to handle just about any operational situation you can imagine
Gate Crafters has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.
