The Estate Swing 433 MHz transmitter module is a very unique product that can make almost any accessory into a wireless accessory. This transmitter module has two activation wires. For any accessory that normally gets wired into a gate opener that simply momentarily closes a dry contact (which is just about any keypad, loop detector, exit wand, push button, or photocell) simply wire the two activation wires into the terminals or wires that normally lead back to the gate opener for activation. When the accessory relay triggers closing the dry contact the transmitter is activated and send a wireless signal to the receiver on the gate opener just like a remote would. Please note with the accessory you are making wireless with this device: you will still need to plan to power your accessory - some accessories can run off batteries and some cannot. Please be aware that you may need to run some lines from a power source to your accessory even if you are converting its triggering of the gate opener to wireless.

The transmitter module is small in size and can fit into the housings of many different accessories. It is 2 1/2 x 1 1/4 x 1/4 inches and connects to a 9V battery. For those devices that cannot fit this transmitter module into its housing, we have an option with a very small plastic box to mount near the accessory.

Convenience is the first thing that comes to mind for most when deciding to convert an accessory to wireless. It is an easier installation when you do not have to run wires 40 or 50 feet to your keypad or another accessory. It can also save you money as the wire is one of those installation materials whose cost can add up quickly depending on the footage needed. There is another advantage to wireless, however. The more wires you have running underground and leading to the control board of the gate opener the higher your power surge/lightning risks become. Transient voltage carries through the ground during a lightning storm and can be picked up by wires running through the ground. If you have many wires tied back to your gate opener control board you are increasing your chances of having to replace a very expensive component of your gate opener system.

	GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have developed videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.

• Module Only: This is just the module without a housing. You will need to insert this into the housing of the accessory and provide a 9 volt battery.


• Module w/ Housing: This is a package with the transmitter module and a plastic housing box for the module and the battery. You will need to provide a 9 volt battery, a dab of caulk, a screw appropriate for the material you are mounting the box too, and possibly additional wire depending how far you are mounting the transmitter module from the accessory.

	GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own automated gates, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.

System shuts off 15 seconds after TALK button is pressed. Press TALK button to turn on again. Dimensions: 4-3/4inch H, 3-1/2inch W, 1-1/8inch D, Weight: 0.31 lbs.

	GateCrafters.com has the resources you need. How do you use your gate opener system once you get it? GateCrafters.com is the only retailer to give a real answer to this question. We have develop videos for installing many of our gate openers and products and write DIY focused manuals for most gate openers and have individual instructions for each accessory to be installed with each gate opener.

None.

	GateCrafters.com has actual experience. We have a testing area, we have factory and internal training courses, we build gates and have our own gates that are automated, we attended all industry trade shows in multiple countries and are a member of the AFA, and we pay visits to our chosen manufacturers' factories. All these factors are what have lead to us having so many exclusive additions. When you see and actually use as many products as we have you tend to have many ideas for minor changes that have major impacts. We acted on these ideas and have utilized them to help thousands of customers automate their gates.